Wireless ESO Plunger Arrival Sensor

Specifications

Specification	XBee (standard)	XBee-PRO (special option)
Performance
Outdoor RF line-of-sight Range	Up to 300 ft (90 m)	Up to 1 mile (1600 m)
Transmit Power Output	1mW (0 dBm)	63mW (18dBm)
RF Data Rate	250,000 bps	250,000 bps
Serial Interface Data Rate	1200 bps - 250 kbps	1200 bps - 250 kbps
Receiver Sensitivity	-92 dBm (1% packet error rate)	-100 dBm (1% packet error rate)
Power Requirements
Supply Voltage	2.8 – 3.4 V	2.8 – 3.4 V
Transmit Current (typical)	45mA (@ 3.3 V)	250mA (@3.3 V)
Idle / Receive Current (typical)	50mA (@ 3.3 V)	55mA (@ 3.3 V)
Power-down Current	< 10 µA	< 10 µA
General
Operating Frequency	ISM 2.4 GHz	ISM 2.4 GHz
Operating Temperature	-40 to 85º C (industrial)	-40 to 85º C (industrial)
Agency Approvals
United States (FCC Part 15.247)	OUR-XBEE	OUR-XBEEPRO
Industry Canada (IC)	4214A XBEE	4214A XBEEPRO
Information courtesy Product Manual IEEE® 802.15.4 RF Modules by Digi International

Mounting Instructions:
Find highest mounting point on wellhead for transmitter with line of sight to receiver. Remove one side of the yellow bracket from the transmitter enclosure mounting post. Place transmitter enclosure on mounting point and reattach yellow bracket to post of transmitter enclosure. Tighten both mounting post nuts evenly to 45 inch pounds. Follow instructions and properly mount plunger arrival sensor to lubricator. If your sensor is already wired to transmitter skip to step 12. Cut cable (if needed) to proper length. Attach to supplied TMCX type explosion proof fitting using instructions provided with fitting. Please be aware of 24 hour drying time! Thread TMCX type fitting into transmitter and tighten. Connect wires from arrival sensor to input wires in receiver red to red, white to white, black to black using supplied connectors. Hook up battery and replace cap. Move to Controller Mount receiver to highest possible position with line of sight to transmitter. Cut cable (if needed) to proper length. Wire receiver to controller. Red wire to power, white wire to counter/plunger input, black to common. Recheck wiring Do Not hook up receiver incorrectly. It may be permanently damaged Test sensor.

Find highest mounting point on wellhead for transmitter with line of sight to receiver.
Remove one side of the yellow bracket from the transmitter enclosure mounting post.
Place transmitter enclosure on mounting point and reattach yellow bracket to post of transmitter enclosure.
Tighten both mounting post nuts evenly to 45 inch pounds.
Follow instructions and properly mount plunger arrival sensor to lubricator.
If your sensor is already wired to transmitter skip to step 12.
Cut cable (if needed) to proper length.
Attach to supplied TMCX type explosion proof fitting using instructions provided with fitting.
Please be aware of 24 hour drying time!
Thread TMCX type fitting into transmitter and tighten.
Connect wires from arrival sensor to input wires in receiver red to red, white to white, black to black using supplied connectors.
Hook up battery and replace cap.

Move to Controller
Mount receiver to highest possible position with line of sight to transmitter.
Cut cable (if needed) to proper length.
Wire receiver to controller. Red wire to power, white wire to counter/plunger input, black to common.
Recheck wiring Do Not hook up receiver incorrectly. It may be permanently damaged
Test sensor.

2150 West 6th Avenue, Suite A
Broomfield, CO 80020
Phone: (303) 460-7481 or Toll Free (877) 460-7481
FAX: (303) 460-7486